Crest Electronics CDVS-7000 Instrukcja Użytkownika Strona 89
- Strona / 341
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
User Manual
i Series / iX Series 75
4.2.13 MEASUREMENT CAL FACTORS Menu
Figure 4-26: MEASUREMENT CAL FACTORS menu
The MEASUREMENT CAL FACTORS menu provides access to the measurement calibration
parameters. For three phase configurations, the PHASE keys toggle between the three
calibration screens for each phase. These parameters are password protected and can only be
changed after the calibration password has been entered. Refer to the calibration section in this
manual for details on performing a calibration.
The following calibration factors are available from this menu:
Entry Description
VOLT FS Full scale voltage measurement calibration factor.
VOLT 0 Zero offset voltage measurement calibration factor.
VOLT FS HT Temperature compensated full scale voltage measurement
calibration factor.
VOLT 0 HT Temperature compensated zero offset voltage measurement
calibration factor.
CURR FS Full scale current measurement calibration factor.
CURR 0 Zero offset current measurement calibration factor.
CURR FS HT Temperature compensated full scale current measurement
calibration factor.
CURR 0 HT Temperature compensated zero offset current measurement
calibration factor.
- AC Power Source 1
- User Manual 1
- SAFETY SYMBOLS 7
- 1. Introduction 15
- 2. Specifications 16
- 2.2 Mechanical 24
- 2.3 Environmental 24
- 2.4 Regulatory 26
- 2.5 Front Panel Controls 26
- 3.1 Unpacking 29
- 3.2 Power Requirements 29
- 3.3 Mechanical Installation 30
- 3.4 Input Wiring – TB1 30
- 3.6 Connectors - Rear Panel 32
- Description 33
- Centronics 36
- Connector 36
- > 400 uS 36
- 24 i Series / iX Series 38
- 3.8 Output Voltage Ranges 40
- 3.9 Functional Test 41
- 28 i Series / iX Series 42
- 30 i Series / iX Series 44
- 34 i Series / iX Series 48
- 4. Front Panel Operation 51
- FUNCTION 53
- 4.2 Menu Structure 56
- 44 i Series / iX Series 58
- 4.2.2 Overview of Menu 1 58
- 4.3 Output Programming 91
- 4.5 Standard Measurements 97
- 4.7 Transient Programming 108
- 5. Principle of Operation 115
- 5.2 Overall Description 116
- 5.3 Oscillator Assembly 116
- 104 i Series / iX Series 118
- 5.4 Current Limit Board 119
- 5.5 Auxiliary Power Supply 119
- 5.6 DC-DC Power Converter 120
- 5.7 AC Control Logic 120
- 108 i Series / iX Series 122
- 5.8 AC Power Board 123
- 5.9 Input/Output Board 123
- 110 i Series / iX Series 124
- CAUTION 126
- 6. Calibration 127
- 118 i Series / iX Series 132
- 6.6 Non-Routine Calibration 134
- 124 i Series / iX Series 138
- 7. Service 139
- 9. Options 147
- 138 i Series / iX Series 152
- Refer to 157
- 158 i Series / iX Series 172
- 9.1.2.8 160 Test Selection 172
- 164 i Series / iX Series 178
- 168 i Series / iX Series 182
- 170 i Series / iX Series 184
- 172 i Series / iX Series 186
- 174 i Series / iX Series 188
- 176 i Series / iX Series 190
- 178 i Series / iX Series 192
- 9.2 IEC 61000-4-11 Option 194
- 9.3 IEC 61000-4-13 Option 201
- 196 i Series / iX Series 210
- 9.4 EOS Option 213
- 206 i Series / iX Series 220
- 208 i Series / iX Series 222
- Figure 9-39: 15003iX/3-EOS3 222
- 9.5 Mode iX Option 228
- 218 i Series / iX Series 232
- 9.6 Omni Options 236
- 226 i Series / iX Series 240
- 228 i Series / iX Series 242
- Power Switch and Lamp 244
- 80-250V SYNC INPUT FROM iX 250
- SOURCE INPUT,OR 250
- OTHER AC LINE VOLTAGE 250
- 9.8.2.8 704 Test Selection 273
- 260 i Series / iX Series 274
- 262 i Series / iX Series 276
- 266 i Series / iX Series 280
- 268 i Series / iX Series 282
- 270 i Series / iX Series 284
- 272 i Series / iX Series 286
- 274 i Series / iX Series 288
- 276 i Series / iX Series 290
- 278 i Series / iX Series 292
- 280 i Series / iX Series 294
- 282 i Series / iX Series 296
- 284 i Series / iX Series 298
- 286 i Series / iX Series 300
- 9.9.7 ABD Test Selection 309
- 296 i Series / iX Series 310
- 298 i Series / iX Series 312
- 302 i Series / iX Series 316
- Controls 319
- 308 i Series / iX Series 322
- 310 i Series / iX Series 324
- 312 i Series / iX Series 326
- 314 i Series / iX Series 328
- 9.10 WHM Option 331
- 10. Error Messages 334
- 322 i Series / iX Series 336
- 324 i Series / iX Series 338
- Table 10-1: Error Messages 338
- 11. Index 339
Powiązane produkty i podręczniki dla Cyfrowe rejestratory wideo (DVR) Crest Electronics CDVS-7000
(30 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.101 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji